Livraison offerte en point relais à partir de 59€

Que recherchez-vous ?

Découvrez nos nombreuses créations à réaliser vous-même...

Lotus Flower Earrings

Symbol of strength, rebirth and purity, Lotus flowers also represent self-improvement and personal accomplishment.

Here we have imagined an airy earring like lotus flowers, with small mother-of-pearl beads for a pure and delicate look.

Follow our step-by-step guide below to make this superb piece of jewelry yourself!

Beautiful achievement  !

For this achievement you need:

2 24K Gold Stud Earring Holders
2 24K Gold Twisted Ring Pendants
2 lotus flower cups
2 rings 5mm 24K Gold
2 flat head nails 24K gold
2 mother-of-pearl beads 8mm
2mm faceted mother-of-pearl beads
Miyuki delica beads 11/0
0.4mm soft brass wire 24K gold

Tools to use:

pliers for jewelry creations

This piece of jewelry is not complicated to make. Follow the steps below carefully and proceed in the same order for easy assembly!

The assembly:

To begin, you will need an 8mm mother-of-pearl bead, a flat head nail and a Lotus flower cup. The bead will fit into the heart of the petals and allow the cup to hold on the nail.

First thread the pearl onto the nail and then place the cup. Hold the cup gently without forcing it so as not to break it!

Then form a loop large enough to fit into the pendant.

Now open the loop made in a spiral with flat pliers and then position it inside the circle pendant. This step is a little tricky, hold the loop with the pliers, this will allow you to guide the nail through the hole in the pendant more easily.

Still using the flat pliers, close the loop, in the opposite direction, to secure the assembly. Make sure that the loop is properly closed and well aligned.

Now start assembling the beads located on the edge of the pendant.

Cut a brass wire of about 20cm and thread 2 Miyuki 11/0 beads, a 2mm mother-of-pearl bead and 2 Miyuki beads again.

Place the beads in the center of the wire then position the centered beads at the lower outer edge of the pendant.

Twist the wire around the pendant 2 times on each side of the beads. For a small wave effect, do not glue the beads to the pendant, leave a small space to create a curve of beads.

Continue like this on each side of the central beads. Tighten the wire tightly around the pendant.

7 small waves of pearls then wrap the wire around 3 turns tightly. Cut the excess flush with the last turn and on the back of the pendant.
Flatten the cut wire slightly with flat pliers, taking care not to damage the wire!

Finally, open a 5mm ring with 2 flat pliers then insert the pendant and the earring holder, making sure to position them in the right direction.

Close the ring, checking that it has returned to its axis and that there is no crack.

Your jewel is finished!

Beautiful creation!

Find all the supplies you need to make this piece of jewelry at the bottom of the page.



Hammered sequin stud earrings in premium 24K fine gold-plated brass €4.50 EUR
50 rings 5mm in brass gilded with 24K fine gold Premium Quality €3.80 EUR
Large twisted circle pendant in premium 24K fine gold-plated brass €3.90 EUR
Double petal flower bowl in gradient pink acrylic €2.40 EUR
8 round pearls 8mm of white mother-of-pearl €3.90 EUR
20 Flat head nails 25mm in premium 24K fine gold-plated brass €2.90 EUR
10 butterfly clasps for BO in premium 24K fine gold-plated brass €1.80 EUR
Soft brass wire 0.4mm in 24K fine gold-plated brass per 1 meter Premium coupon €1.00 EUR
38cm thread of natural 2mm faceted mother-of-pearl beads €8.00 EUR
5 grams of Miyuki Délica beads 11/0 Duracoat Galvanized Gold DB1832 €3.80 EUR
Pink cutting pliers for jewelry creation €5.95 EUR
Pink curved flat pliers for jewelry creation €5.95 EUR
Pink Flat Pliers for Jewelry creation €5.95 EUR
Large Twisted Circle Pendant in 925 Premium Silver Brass €3.80 EUR
Pink round tip pliers for jewelry creation €5.95 EUR
Beading thread 8mm irregular natural mother-of-pearl €11.00 EUR
8mm round pearl thread in white mother-of-pearl €18.00 EUR