Livraison offerte en point relais à partir de 59€

Que recherchez-vous ?

Découvrez nos nombreuses créations à réaliser vous-même...

Wisteria Necklace

Symbol of love and complicity, the flowers of Wisteria are among the most beautiful climbing plants. They represent the bond of reciprocal friendship, it uses the support of its neighbors and comes to sublimate them in return, trees, walls ...

Here I imagined a creation in variation of our earrings. A string of mother-of-pearl beads with a few beads in purple hues to recall the wisteria flowers.

I hope you like this gem!

Follow our very simple step-by-step guide to make this superb piece of jewelry yourself!

Beautiful achievement  !

For this achievement you need:

21cm nugget chain
Griffin 0.35mm transparent nylon thread
1 strand of mother-of-pearl beads
11 flat head nails 24K gold
6 round bohemian beads 4mm
5 Bohemian pearl drops
2 rings 3mm 24K Gold
1 24K Gold Clasp
1 closed ring 6mm 24K gold
2 crush beads

Tools to use:

pliers for jewelry creations

This piece of jewelry is not complicated to make. Follow the steps below carefully and proceed in the same order for easy assembly!

The assembly:

I will give you the instructions for a 40cm choker necklace, but feel free to adjust the size to your taste by lengthening either the chains or the row of pearls. In this case, consider taking 2 mother-of-pearl threads.

To begin, mount the 4mm round beads on flat head nails and form normal sized loops. The loop made should measure approximately 3mm in diameter for a nice discreet result.

Then mount 5 drop beads on flat head nails. Make loops of the same size as the previous ones.

Then cut a transparent nylon thread of about 30cm.

Here we will start from the center of the necklace and then mount the beads in symmetry. This method allows you to adjust the length and threading without having to remove everything if it does not suit you.

First thread a drop pearl in the center, on each side place a mother-of-pearl pearl.

Thread a 4mm bead on each side then another mother-of-pearl bead.

Continue in this way until you have placed all the drop and 4mm pearls alternating with the mother-of-pearl.

Finish the threading with the remaining mother-of-pearl beads in symmetry.

Now we are going to connect the pearl thread to the chains. Here I offer you a simple and easy version to connect a string of pearls to chains.

First, cut 2 pieces of chain of 10.5cm. Here for a necklace of 40cm. Adjust the length if necessary.

Thread a crimp bead onto the nylon thread, then pass the thread through the chain link.

Pass the wire back through the crimp bead and then, using flat pliers, bring the bead back to the edge of the chain link. Crush the bead with the flat pliers.

Cut off the excess wire at the edge of the bead.

For the other side, do as before, but before flattening the pearl, make sure to keep some flexibility in the string of pearls. Your necklace should remain fluid without stiffness between the pearls.

Finally, connect the clasp with a 3mm ring to the end of one of the chains. On the other side, place the ring closed with a 3mm ring.

Check that your rings are properly closed.

Your jewel is finished!

Beautiful creation!

Complete your creation with the matching earrings!

Find all the supplies you need to make this piece of jewelry at the bottom of the page.



Bohemian beading thread striped drops 15x8mm Pastel purple €3.20 EUR
Thread of round Bohemian pearls 4mm transparent purple €2.40 EUR
20 Flat head nails 25mm in premium 24K fine gold-plated brass €2.90 EUR
Spool of 50 meters of transparent Nylon thread 0.35mm Griffin €2.50 EUR
Thread of small 5mm irregular natural mother-of-pearl beads €8.90 EUR
4 buoy clasps 5mm in 24K Premium gold-plated brass €2.30 EUR
10 closed rings 6mm in brass Gilded with 24K Premium fine gold €1.80 EUR
Thread of round Bohemian pearls 4mm transparent burgundy brown €2.50 EUR